» Welcome Gast   | Register

PC Forum
English
Answer in: Wire Mod Question!

Answer to Wire Mod Question!
Username:   Not registered yet?
Password:   Forgot password?
iB Code Einmal klicken um den Tag zu öffnen, nochmal klicken zum Close

Top Smilies
Beitrag

HTML ist on für dieses Forum

IkonCode ist on für dieses Forum

SMILIES LEGENDE ansehen
Beitragsoptionen

 Would you like to add your signature?
Do you want to be informed about answer by email?
Do you want to activate emoticons in your post?
 

Review of postings for Wire Mod Question! (the latest posts first)
Beomaster Erstellt: 23:07 am 21. Jan. 2008
yes its possible with a thin extreme sharp knife, but dont cut too deep
gh0st Erstellt: 22:30 am 21. Jan. 2008
I'm sure it's a stock heatsink and fan. : (

Could I just cut the L11 bridge with a knife and be done with it?
Beomaster Erstellt: 12:59 am 21. Jan. 2008
without cutting L11 bridges you are only able to add voltage to the step of open bridges, what means:
L11 says 1,50V, you can wire mod 1,55 1,60 1,65 1,70 1,75 1,80 and 1,85V
L11 says 1,60V, you can wire mod 1,65 1,80 and 1,85V
L11 says 1,65V, you can wire mod only 1,85V
you only have to set a few wires for changing voltage, look what wires must be set for stock voltage, imagine theese are already set, you only have to add the wire(s) for the voltage you need
you can use 1,85V but be sure you have a damn good cooler, TMax should be maximum 55°C to be safe
gh0st Erstellt: 3:59 am 21. Jan. 2008
Thanks for the replies! I did finish it. Now I have another kind of issue though:

I opened my bios util PC Health, and it says the CPU voltage is at ~1.8 now. I am almost positive I set the wires for 1.675.

It's faster, but won't the 1.8 burn it up? It was at 114F and climbing when I turned it off. It was only really on though for 2-4 minutes.

Help!

Thanks.
Beomaster Erstellt: 13:47 am 19. Jan. 2008
he means 5.5x333, we say 11x166 and right, do the wire trick, its really easy
the silverstuff you may get from car repair, its used to fix damaged window heat
Weniger Answer Mehr Answer
Schermi74 Erstellt: 8:49 am 19. Jan. 2008
Hello,

you dont need to work with the Lasercuts, you simply can do the  Pin-Mod its way easier und you can undo it if you have to, just cut some Wires from a cable, form them as an "U" and stuck them into the holes.

But why is your CPU running with a Multiplier of 5.5?:noidea:
gh0st Erstellt: 4:34 am 19. Jan. 2008
Hello.

I am new to overclocking. I have a AMD Barton 2500+ on a board with no multiplier, vdimm, or vcore options, just fsb, an agressive/optimal cpu option and memory timings and speed. It supports 200fsb but I can't get the 2500 to that speed (on the stock 5.5 multiplier) with stability. So I was wanting to increase the vcore to 1.675 as opposed to the 1.65 it's at now.

I'm confused on what I need to do on top of the processor? What bridges should I cut or fill?

Should I just wire it to lower the multiplier? I'm really just after the 200fsb so I can take advantage of the DDR400 in there.

Where can I get some of that silver stuff?

Thanks!

(Geändert von gh0st um 4:40 am Jan. 19, 2008)


(Geändert von gh0st um 4:42 am Jan. 19, 2008)
×